Lexus Airbag Light After Cluster Removal: Code 41 Reset Guide

If the airbag light appeared after your Lexus instrument cluster was removed, one question matters: was the ignition turned on or the engine started while the cluster was unplugged? That can leave a stored airbag warning after the cluster is reinstalled. In this situation, the stored warning does not, by itself, mean the instrument cluster or our repair is defective.

This guide explains the Tc/AB airbag memory-reset sequence for Lexus models that use this diagnostic procedure, including the familiar early LS and SC applications. The sequence is not limited to the LS400, but connector location, terminal layout and diagnostic-code definitions can vary. Confirm the Tc and AB terminals and the applicable factory procedure on the actual vehicle before connecting wires.

When this reset is appropriate

Use this procedure only after the cluster is correctly reconnected, the applicable diagnostic code has been identified, and any underlying fault has been corrected. Code 41 is a stored-memory indication; clearing it does not repair damaged wiring, sensors or other restraint-system components. A light that returns, remains on, or appeared without the disconnected-cluster scenario needs SRS diagnosis.

Before connecting any wires

  • Park the vehicle, keep the engine off, and begin with the ignition in LOCK/OFF.
  • Confirm the diagnostic connector and its Tc and AB labels using the vehicle’s factory information. On the LS400 covered by the LexLS guide, the TDCL is under the driver’s side of the dash near the parking brake.
  • Identify terminals by their labels—not wire colors, a photograph’s orientation or a guessed pin position. If the labels or procedure do not match your vehicle, stop.
  • Use insulated service wires and a verified body ground. Do not probe airbag connectors, apply battery voltage to SRS wiring or bridge unrelated terminals. Have a qualified technician perform the procedure if you cannot positively identify the diagnostic terminals.

The Tc / AB reset sequence

  1. With the ignition off, attach separate service wires to diagnostic terminals Tc and AB. Keep their free ends isolated. Prepare a separate lead connected to a verified body ground.
  2. Turn the ignition to ACC or ON without starting the engine. Wait at least six seconds.
  3. Ground the Tc and AB leads in the order below. During each changeover, release the previous lead and make the next ground connection within 0.2 second.
StageLead connected to body groundDuration
1TcAbout 1 second
2ABAbout 1 second
3TcAbout 1 second
4ABAbout 1 second
5TcHold for several seconds; leave AB ungrounded

For the one-second stages, the LexLS guide specifies a 0.5–1.5-second range. The quick changeover between leads is the critical part. Successful clearing is indicated by rapid, continuous flashing of the airbag warning lamp, rather than the slower diagnostic-code pattern.

After the clearing indication, return the ignition to LOCK/OFF, remove the service wires and refit the diagnostic connector cover. Check the warning lamp’s normal self-test using the applicable factory instructions. A successful memory reset alone is not proof that every SRS component is healthy.

If the light does not clear

Incorrect timing can prevent this sequence from being accepted. Recheck the correct connector, terminal identification, ground and timing before another attempt. Do not keep clearing a warning that returns or use this procedure to bypass another diagnostic code. Have the SRS fault diagnosed if the result is uncertain.

Avoiding the warning after cluster service

Follow the vehicle’s factory battery-disconnection and SRS precautions before removing the cluster. Do not turn on the ignition or start the vehicle while the cluster is unplugged. Reinstall and fully connect the cluster before powering the vehicle again.

For eligible cluster repairs, complete and electronically sign our work order and keep the intake reference with the unit. For vehicle-specific repair questions, contact Tanin Auto Electronix.


Source credit: Adapted in our own wording from the LexLS Code 41 tutorial for the 1990–1994 LS400 (archived copy), with Tanin’s cluster-service guidance. Connector location and reset instructions must be checked against the factory information for the actual vehicle. This is not a general airbag repair procedure.

Shopping Cart
Scroll to Top